Tate: /* 70cm Repeaters */

2025-04-11T22:50:28Z

70cm Repeaters

← Older revision		Revision as of 22:50, 11 April 2025
Line 52:		Line 52:

	== 70cm Repeaters ==		== 70cm Repeaters ==
	# '''449.575''' 173.8hz tone - [http://status.irlp.net/?nodeid=7707 KD7AGA - IRLP node 7707].		# '''448.000-''' 703 DCS - this is, at best, an on campus only system due to where the antenna is located. Hope is that'll change, one day.
			# '''449.575-''' 173.8hz tone - [http://status.irlp.net/?nodeid=7707 KD7AGA - IRLP node 7707].
	#*[http://www.irlp.net/guidelines.html IRLP usage guidelines]		#*[http://www.irlp.net/guidelines.html IRLP usage guidelines]
	#*See The [[KD7AGA IRLP DTMF]] page for some of the customized, local commands available.		#*See The [[KD7AGA IRLP DTMF]] page for some of the customized, local commands available.
	# '''449.500''' 100.0hz tone - NB7I		# '''449.500-''' 100.0hz tone - NB7I

	== Standard Offsets ==		== Standard Offsets ==

Tate: Created page with "450px == State Repeater Information == See the Wyoming Repeaters page for more. = Voice Repeaters = '''All repeaters listed are 'open' to all licensed operators.''' All CARC sponsored repeaters use CTCSS input tones in accordance with good engineering practice, not to restrict access. == Linked Systems == ===WyoComm=== WyoComm is a growing, not-quite state wide linking system that allows voice communi..."

2022-12-09T23:46:42Z

Created page with "right|thumb|450px == State Repeater Information == See the Wyoming Repeaters page for more. = Voice Repeaters = '''All repeaters listed are 'open' to all licensed operators.''' All CARC sponsored repeaters use CTCSS input tones in accordance with good engineering practice, not to restrict access. == Linked Systems == ===WyoComm=== WyoComm is a growing, not-quite state wide linking system that allows voice communi..."

New page

[[File:Repeater graphic.jpg|right|thumb|450px]]

== State Repeater Information ==
See the [[Wyoming_Repeaters | Wyoming Repeaters]] page for more.

= Voice Repeaters =
'''All repeaters listed are 'open' to all licensed operators.'''

All CARC sponsored repeaters use CTCSS input tones in accordance with good engineering practice, not to restrict access.

== Linked Systems ==
===WyoComm===
WyoComm is a growing, not-quite state wide linking system that allows voice communications across large areas of Wyoming with common 2m gear - often hand helds! See the [[WyoComm]] page for information and details. See the [[Wyoming_Repeaters | Wyoming Repeaters]] page for more.

==2m Simplex==
See the [[2m_simplex | WY 2m Simplex]] page for suggested simplex channel spacing.

== 2m Repeaters ==
This [[2m-coverage | Page]] has coverage maps - may be useful in deciding what repeaters you want to use.

# '''[[146.940]]''' 123.0Hz tone (146.340) - W7VNJ
#* Part of the [[WyoComm]] linked repeater system.
#* Wider area (regional) repeater on Casper Mnt.
#* Linked with 146.805 on Copper Mnt.
#*''note: Also transmits a 123.0Hz tone on it's output.''
#* The WyoComm link on Copper Mtn. has partially failed resulting in a one way connection so the link has been turned off until repairs can be made.
#* [[2m-coverage | Loca coverage map]]
# '''145.235''' 100Hz tone (144.635) - W7VNJ
#* Wider area (regional) repeater on Casper Mnt. [[Autopatch-Rules | '''Autopatch''']]
#** Please read the "[[Autopatch-Rules |Rules of the Road]]" for autopatch use. Does not have reverse autopatch.
#** Use * (star) to "Bring Up" the autopatch - dial a call.
#** Use # (pound) to "Down" the autopatch - hang up
#* [[2m-coverage | Local coverage map]]
#* Wider area (regional) repeater on Casper Mnt.
#* ''note: Also transmits a 100Hz tone on it's output.''
# '''147.280+''' DCS 032 (147.880) - W7VNJ
#* Local Repeater in Casper - located at Wyoming Medical Center
#* Yaesu System Fusion - DCS 032
# '''146.910''' 100.0Hz tone (146.310) - ??
#* Location?
# '''147.345''' (no PL) (147.945) - K7KMT
#* Location?
# '''146.805''' 100Hz tone (146.205) - ??
#* Copper Mountain repeater - Covers: Riverton, Thermopolis and Lander(?)
#* [[WyoComm]] Hub
#* [[2m-coverage | 2m coverage map]]

'''NOTE:'''Some of our repeaters also transmit the same PL tone they use on RX. This allows each operator the option to use CTCSS on their receivers. Wether or not you choose to use CTCSS, repeater usage and operation is not changed.

=== Coverage ===
[[2m-coverage | This page]] has coverage maps for most of the W7VNJ repeaters.

== 70cm Repeaters ==
# '''449.575''' 173.8hz tone - [http://status.irlp.net/?nodeid=7707 KD7AGA - IRLP node 7707].
#*[http://www.irlp.net/guidelines.html IRLP usage guidelines]
#*See The [[KD7AGA IRLP DTMF]] page for some of the customized, local commands available.
# '''449.500''' 100.0hz tone - NB7I

== Standard Offsets ==
* Traditionally, repeaters are named for their output frequency.
* Unless noted in a repeaters listing, the following standard offsets apply.

{| border="1"
|+ '''Standard Repeater Offsets'''
! Output Mhz !! Direction !! Offset Mhz
|-
! 51 - 52
| align="center" | Neg ||align="center" | 0.5
|-
! 52 - 54
| align="center" | Neg ||align="center" | 1.0
|-
! 144.51 - 144.89
| align="center" | Pos ||align="center" | 0.6
|-
! 145.11 - 145.49
| align="center" | Neg ||align="center" | 0.6
|-
! 146.0 - 146.39
| align="center" | Pos ||align="center" | 0.6
|-
! 146.61 - 147.0
| align="center" | Neg ||align="center" | 0.6
|-
! 147.0 - 147.39
| align="center" | Pos ||align="center" | 0.6
|-
! 147.6 - 147.99
| align="center" | Neg ||align="center" | 0.6
|-
! 440 - 445
| align="center" | Pos ||align="center" | 5.0
|-
! 445 - 450
| align="center" | Neg ||align="center" | 5.0
|}

*Taking the published output of 146.940Mhz and the standard offset indicated, that repeater's input frequency is 146.340Mhz.<br>

== Repeater etiquette ==
A [[Repeater_etiquette | very basic primer]] on how to not embarrass yourself - too badly - on the "local repeater". Just remember, we've all done it - at least once. We'd much rather you "get in there" and pull a whopper than not use the repeaters at all. As nothing is done maliciously, give it a go!

= Digital Systems =

== APRS infrastructure ==
All APRS traffic is on '''144.390''' - Unconnected Information (UI) frames, AX.25. Traditional paths using RELAY,WIDE or WIDEn-n and the newer WIDEn-n only paths will work. TRACE and TRACEn-n are also supported. Please keep your paths reasonable. 2 or 3 hops is usually sufficient.
* Suggested paths:
** Mobiles: WIDE3-3
** Fixed Stations: WIDE2-2
Excessive paths (such as WIDE7-7, etc) will often land you on a digipeater's 'LID List' - blocked out of that digipeater. This isn't a punitive action - but rather an attempt to protect the RF network from packet floods in neighboring areas.

=== Internet Gateways and public servers ===
# KE7AZF-1 - [http://map.findu.com/ke7azf-1 I-gate], East side (occasional, fill-in and backup)

===(TM)===
APRS is a registered trademark of APRS Software and Bob Bruninga, WB4APR.

== Traditional Packet ==
I know of no connected mode amateur AX.25 activity in Wyoming. Though I have heard of a rumor of a BBS in the Casper area? No details at this time. Anyone able to fill in?

Area Repeaters - Revision history

Tate: /* 70cm Repeaters */